-
Gyuto (Chef's Knife)
225mm ProCut +Wrought Iron San-Mai Gyuto
$50.00This 225mm ProCut blade will be my first available in this new and innovative steel. I’ve elected to utilize san-mai construction for my ProCut blades owing to the costs associated with acquiring it. ProCut is a brand new steel released by Pop’s Knife Supply and Larrin Thomas. You could think of ProCut as a steel with the toughness of 80CrV2, the nickel content of 15n20 and edge retention somewhere between 52100 and AEB-L.
This 225mm ProCut blade features a stone tuned geometry and a very fine 2500 grit finish that was finished with my own special polishing mix that results in a kasumi-like finish without the use of uchigumori
Please note that there is a small blemish in the handle where a chip was repaired during construction.
Blade Details
Blade: 224mmx51mm ProCut+ Wrought Iron (~64/65 hrc) Stone tuned bevels + 2500 grit hand finish + pseudo uchigumori/kasumi polish.
Neck: 17mmx18mm
Handle: Stabilized amboyna burl, oil finished, buffed and waxed
POB: 42mm from the handle
Spine: 3.29mm at the handle, 2.70mm at halfway, .65mm 1cm from the tip
Grind: full convex RH bias
Weight: 183g
Relieved choil and spine
Edge: .17mm@1mm, .28mm@2mm from the edge, measured at the midpoint
Blade Special Features
Fully convex ground blade, wrought iron clad.
To learn more about ProCut steel click here: https://knifesteelnerds.com/2025/06/04/pops-procut-a-new-carbon-steel-for-knives/
-
Kitchen Knives
240mm ProCut San-Mai Gyuto
$50.00This 240mm ProCut blade will be my second available in this new and innovative steel. I’ve elected to utilize san-mai construction for my ProCut blades owing to the costs associated with acquiring it. ProCut is a brand new steel released by Pop’s Knife Supply and Larrin Thomas. You could think of ProCut as a steel with the toughness of 80CrV2, the nickel content of 15n20 and edge retention somewhere between 52100 and AEB-L.
This 240mm ProCut blade features a stone tuned geometry and a very fine 2500 grit finish that was finished with my own special polishing mix that results in a kasumi-like finish without the use of uchigumori. This finish highlights the core steel while creating a smokey haze where some minor carbon migration has occurred and leaves subtle intimations of the endogenous banding within the cladding steel. Interestingly enough it even highlighted a couple of inclusions within the cladding steel.
Blade Details
Blade: 240mmx51mm ProCut+ Low carbon steel (~64/65 hrc) Stone tuned bevels + 2500 grit hand finish + pseudo uchigumori/kasumi polish.
Neck: 17mmx19mm
Handle: Stabilized/dyed maple burl and paper micarta, oil finished, buffed and waxed
POB: 40mm from the handle
Spine: 3.53mm at the handle, 2.42mm at halfway, .68mm 1cm from the tip
Grind: full convex RH bias
Weight: 196g
Relieved choil and spine
Edge: .16mm@1mm, .27mm@2mm from the edge, measured at the midpoint
Blade Special Features
Fully convex ground blade, low carbon clad.
To learn more about ProCut steel click here: https://knifesteelnerds.com/2025/06/04/pops-procut-a-new-carbon-steel-for-knives/
-
Kitchen Knives
190mm ProCut San-Mai Gyuto With Banding
$50.00This 190mm ProCut San-Mai Gyuto represents a large step forward in my polishing abilities. In this blade the various hues of carbon diffusion are visible at the weld interface while the cladding itself carries a natural mural of alloy banding patterns that exist within the steel itself.
Blade Details
Blade: 190mmx55mm ProCut+ stainless steel (~64/65 hrc) Stone tuned bevels + 2500 grit hand finish + pseudo uchigumori/kasumi polish.
Neck: 18mmx19mm
Handle: Stabilized/dyed maple burl and paper micarta, oil finished, buffed and waxed
POB: 30mm from the handle
Spine: 3.26mm at the handle, 2.54mm at halfway, .71mm 1cm from the tip
Grind: full convex RH bias
Weight: 173g
Relieved choil and spine
Edge: .14mm@1mm, .29mm@2mm from the edge, measured at the midpoint
Click HERE for close up video
Blade Special Features
Fully convex ground blade, stainless clad with active banding.
ProCut is a brand new steel released by Pop’s Knife Supply and Larrin Thomas. You could think of ProCut as a steel with the toughness of 80CrV2, the nickel content of 15n20 and edge retention somewhere between 52100 and AEB-L.
This 190mm ProCut San-Mai Gyuto features a stone tuned geometry and a very fine 2500 grit finish that was polished with my own special mixture that results in a kasumi-like finish without the use of uchigumori. This finish highlights the core steel while creating a smokey haze where some minor carbon migration has occurred and reveals the endogenous banding within the cladding steel.
To learn more about ProCut steel click here: https://knifesteelnerds.com/2025/06/04/pops-procut-a-new-carbon-steel-for-knives/
For the maker’s impression on various steels click here: https://msicardcutlery.com/knife-making-steel-information-faq/
-
Kitchen Knives
160mm 26c3 San-Mai Santoku
$50.00A 160mm 26c3 san-mai santoku
It’s been a while since I posted any new work, it’s been a crazy month and among other things I now have a power hammer in my shop that I’ve been learning how to use. This 160mm 26c3 san-mai santoku is the first of those forged blades to be made available and others will be posted in the coming days. The blade has stone set bevels with good convexity, and while I didn’t go nuts removing every single grinder scratch from the blade 98% of them are gone. Initially I tried a coticule kasumi on one side and got some scratching so I swapped to my uchigumori finger stones to a much better effect and that’s what I’ll stick with from here on out.
- Blade: 160mmx56mm 26c3/mild san-mai (64/65hrc) – stone set bevels + 2500 grit hand finish + finger stone kasumi polish
- Neck: 18mmx19mm
- Handle: Cocobolo+walnut, oil finished and waxed
- POB: 32mm from the handle
- Spine: 2.9mm at the handle, 1.96mm at halfway, 1.65mm 1cm from the tip
- Grind: full convex high bevel 50/5
- Weight: 165g
- Relieved choil and spine
- Edge: .15mm@1mm, .33mm @2mm, 1.7mm at the shinogi measured at the midpoint,
For the maker’s summative take on 26c3 steel click: Here
To learn more about 26c3 steel click Here
-
Kitchen Knives
180m Low Bevel Bunka 26c3 San-Mai
$50.00A 180mm low bevel bunka in 26c3 san mai.
This 180mm low bevel bunka represents the first forging I performed with my new power hammer and my first shot at forged hollow bevels. Overall it came out well but I’m confident I can get things much thinner with a better set of dies. The blade has been tested and it’s as you would expect with these dimensions, it handles like a workhorse and has excellent food release with no stiction. It does require a little bit more force in denser produce but nothing that feels like work.
- Blade: 183mmx51mm 26c3/mild san-mai (64/65hrc) -stone set bevels + 2500 grit hand finish + finger stone kasumi polish
- Neck: 17mmx16mm
- Handle: Red Zebrawood +walnut, oil finished and waxed
- POB: 38mm from the handle
- Spine: 5.4mm at the handle, 5.2mm above the heel, 2.4mm at halfway, 1.98mm 1cm from the tip
- Grind: full convex low bevel 50/50
- Weight: 200g
- Relieved choil and spine
- Edge: .16mm@1mm, .54mm @2mm, 1.74mm at the shinogi measured at the midpoint,
For the maker’s summative take on 26c3 steel click: Here
To learn more about 26c3 steel click Here
-
Kitchen Knives
170mm 26c3 Bunka
$50.00A 170mm 26c3 san mai bunka
- Blade: 170mmx55mm 26c3/mild san-mai (64/65hrc) -stone set bevels + 2500 grit hand finish + finger stone kasumi polish
- Neck: 18mmx18mm
- Handle: Bolivian Rosewood +walnut, oil finished and waxed
- POB: 35mm from the handle
- Spine: 3.1mm at the handle, 3.5mm above the heel, 2.3mm at halfway, 1.61mm 1cm from the tip
- Grind: full convex low bevel 50/50
- Weight: 186g
- Relieved choil and spine
- Edge: ..2mm@1mm, .46mm @2mm, 1.75mm at the shinogi measured at the midpoint,
For the maker’s summative take on 26c3 steel click: Here
To learn more about 26c3 steel click Here
-
Kitchen Knives
140mm 26c3 Sabaki
$50.00A 140mm 26c3 sabaki
The sabaki is a type of Japanese boning knife. Like the honesuki it excels at removing meat from bones and separating joints but it has a more robust design better suited to large mammals than a honesuki.
- Blade: 140mmx25mm 26c3/mild san-mai (64/65hrc) -stone set bevels + 2500 grit hand finish + finger stone kasumi polish
- Neck: 18mmx18mm
- Handle: Burned oak oil finished and waxed
- POB: At the handle
- Spine: 2.6mm at the handle, 2.5mm before the tip
- Grind: full convex low bevel 50/50
- Weight: 97g
- Relieved choil and spine
For the maker’s summative take on 26c3 steel click: Here
To learn more about 26c3 steel click Here
-
Kitchen Knives
230mm Forged Low Bevel Gyuto (26c3)
$50.00A 230mm forged 26c3 san mai gyuto
My forging experiments continue and while I’m getting close to where I want to be, I’ve determined I need better dies to take me the rest of the way. This 230mm forged blade is like the previous ones, and once again I did no go to the extent of taking out all of the grinder marks as it was primarily built as a tool to learn on. The edge geometry is perhaps the thinnest I have ever made and the knife cuts beautifully.
- Blade: 232mmx60mm 26c3/mild san-mai (64/65hrc) -stone set bevels + 2500 grit hand finish + finger stone kasumi polish
- Neck: 18mmx19mm
- Handle: Bolivian Rosewood mono, oil finished and waxed
- POB: 62mm from the handle
- Spine: 2.94mm at the handle, 2.21mm at halfway, 1.32mm 1cm from the tip
- Grind: full convex low bevel 50/50
- Weight: 225g
- Relieved choil and spine
- Edge: .10mm@1mm, .23mm @2mm, 1.65mm at the shinogi measured at the midpoint,
Any US Tariffs will be covered by myself in full.
For the maker’s summative take on 26c3 steel click: Here
To learn more about 26c3 steel click Here
-
Kitchen Knives
205mm MagnaCut San-Mai Gyuto
$750.00Prices are Tariff Inclusive
A 205mm MagnaCut gyuto
Something of a “proof of process” blade this 205mm MagnaCut gyuto features a laminated san-mai blade with a nickel carbon migration barrier between the core and cladding. The bevels are fully convex, and hand finished to 600 grit to enhance both aesthetic appeal and cutting performance. Weight-wise I would categorize this knife as a light midweight. The handle consists of oil finished and buffed Bocote. The choil and spine are nicely rounded as always with signature 600 grit crosshatching.
Blade Details
Blade: 206mmx52mm MagnaCut (~63hrc) with a 600 grit hand finish
Neck: 17mmx18mm
Handle: Bocote, oil finished, buffed and waxed
POB: 30mm from the handle
Spine: 3.04mm at the handle, 2.68mm at halfway, .78mm 1cm from the tip
Grind: full convex 50/50 grind
Weight: 157g
Relieved choil and spine
Edge: .18mm@1mm, .28mm@2mm from the edge, measured at the midpoint
Note: There is a roughly 20mm long and very minor core/cladding separation just ahead of the maker’s mark on the spine. It’s virtually invisible except under direct light.
Blade Special Features
Fully convex ground MagnaCut san-mai blade
To learn more about MagnaCut steel click here: https://knifesteelnerds.com/2021/03/25/cpm-magnacut/
For the maker’s summative take on MagnaCut click here: https://msicardcutlery.com/knife-making-steel-information-faq/
